Linux.pl
Opcje wyszukiwania podręcznika man:
Lista stron man zaczynających się od znaku:
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   ALPHA   NUM   OTHER   ALL
SMARTD.CONF(5)                    2008/03/10                    SMARTD.CONF(5)

NAME
       smartd.conf - SMART Disk Monitoring Daemon Configuration File

FULL PATH
       /etc/smartd.conf

PACKAGE VERSION
       smartmontools-5.38 released 2008/03/10 at 10:44:07 GMT

DESCRIPTION
       /etc/smartd.conf is the configuration file for the smartd daemon, which
       monitors the Self-Monitoring, Analysis and Reporting Technology (SMART)
       system built into many ATA-3 and later ATA, IDE and SCSI-3 hard drives.

       If the configuration file /etc/smartd.conf is present, smartd reads  it
       at  startup,  before  fork(2)ing  into the background. If smartd subse-
       quently receives a HUP signal, it will then re-read  the  configuration
       file.  If smartd is running in debug mode, then an INT signal will also
       make it re-read the configuration file. This signal can be generated by
       typing <CONTROL-C> in the terminal window where smartd is running.

CONFIGURATION FILE /etc/smartd.conf
       In  the absence of a configuration file, under Linux smartd will try to
       open the 20 ATA devices /dev/hd[a-t] and the 26 SCSI devices /dev/sd[a-
       z].   Under  FreeBSD,  smartd will try to open all existing ATA devices
       (with entries in /dev) /dev/ad[0-9]+  and  all  existing  SCSI  devices
       /dev/da[0-9]+.   Under  NetBSD/OpenBSD,  smartd  will  try  to open all
       existing ATA devices (with entries  in  /dev)  /dev/wd[0-9]+c  and  all
       existing SCSI devices /dev/sd[0-9]+c.  Under Solaris smartd will try to
       open  all  entries  "/dev/rdsk/c?t?d?s?"  for  IDE/ATA  and  SCSI  disk
       devices, and entries "/dev/rmt/*" for SCSI tape devices.  Under Windows
       smartd  will  try  to  open  all  entries  "/dev/hd[a-j]"  ("\\.\Physi-
       calDrive[0-9]")  for  IDE/ATA devices on WinNT4/2000/XP, "/dev/hd[a-d]"
       (bitmask from "\\.\SMARTVSD") for IDE/ATA devices on  Win95/98/98SE/ME,
       and  "/dev/scsi[0-9][0-7]"  (ASPI adapter 0-9, ID 0-7) for SCSI devices
       on all versions of Windows.  Under Darwin, smartd  will  open  any  ATA
       block storage device.

       This  can  be  annoying if you have an ATA or SCSI device that hangs or
       misbehaves when receiving SMART commands.  Even if this causes no prob-
       lems,  you  may  be  annoyed  by the string of error log messages about
       block-major devices that can't be found, and SCSI devices that can't be
       opened.

       One  can  avoid  this  problem, and gain more control over the types of
       events  monitored  by  smartd,  by   using   the   configuration   file
       /etc/smartd.conf.   This  file  contains  a list of devices to monitor,
       with one device per line.  An example file is included with the  smart-
       montools  distribution. You will find this sample configuration file in
       /usr/share/doc/smartmontools/. For  security,  the  configuration  file
       should not be writable by anyone but root. The syntax of the file is as
       follows:

       o   There should be one device listed per line, although you  may  have
           lines that are entirely comments or white space.

       o   Any text following a hash sign '#' and up to the end of the line is
           taken to be a comment, and ignored.

       o   Lines may be continued by using a backslash '\' as  the  last  non-
           whitespace or non-comment item on a line.

       o   Note: a line whose first character is a hash sign '#' is treated as
           a white-space blank line, not as a non-existent line, and will  end
           a continuation line.

       Here  is an example configuration file.  It's for illustrative purposes
       only; please don't copy it onto your system without reading to the  end
       of the DIRECTIVES Section below!

       ################################################
       # This is an example smartd startup config file
       # /etc/smartd.conf for monitoring three
       # ATA disks, three SCSI disks, six ATA disks
       # behind two 3ware controllers, two disks on a cciss
       # controller, three SATA disks directly connected
       # to the highpoint rocket-raid controller, two
       # SATA disks connected to the highpoint controller
       # via a pmport device and one SATA disk.
       #
       # First ATA disk on two different interfaces. On
       # the second disk, start a long self-test every
       # Sunday between 3 and 4 am.
       #
         /dev/hda -a -m admin@example.com,root@localhost
         /dev/hdc -a -I 194 -I 5 -i 12 -s L/../../7/03
       #
       # SCSI disks. Send a TEST warning email to admin on
       # startup.
       #
         /dev/sda
         /dev/sdb -m admin@example.com -M test
       #
       # Strange device. It's SCSI. Start a scheduled
       # long self test between 5 and 6 am Monday/Thursday
         /dev/weird -d scsi -s L/../../(1|4)/05
       #
       # An ATA disk may appear as a SCSI device to the
       # OS. If a SCSI to ATA Translation (SAT) layer
       # is between the OS and the device then this can be
       # flagged with the '-d sat' option. This situation
       # may become common with SATA disks in SAS and FC
       # environments.
         /dev/sda -a -d sat
       #
       # Four ATA disks on a 3ware 6/7/8000 controller.
       # Start short self-tests daily between midnight and 1am,
       # 1-2, 2-3, and 3-4 am. Starting with the Linux 2.6
       # kernel series, /dev/sdX is deprecated in favor of
       # /dev/tweN. For example replace /dev/sdc by /dev/twe0
       # and /dev/sdd by /dev/twe1.
         /dev/sdc -d 3ware,0 -a -s S/../.././00
         /dev/sdc -d 3ware,1 -a -s S/../.././01
         /dev/sdd -d 3ware,2 -a -s S/../.././02
         /dev/sdd -d 3ware,3 -a -s S/../.././03
       #
       # Two ATA disks on a 3ware 9000 controller.
       # Start long self-tests Sundays between midnight and
       # 1am and 2-3 am
         /dev/twa0 -d 3ware,0 -a -s L/../../7/00
         /dev/twa0 -d 3ware,1 -a -s L/../../7/02
       #
       # Monitor 2 disks connected to the first HP SmartArray controller which
       # uses the cciss driver. Start long tests on Sunday nights and short
       # self-tests every night and send errors to root
         /dev/cciss/c0d0 -d cciss,0 -a -s (L/../../7/02|S/../.././02) -m root
         /dev/cciss/c0d0 -d cciss,1 -a -s (L/../../7/03|S/../.././03) -m root
       #
       # Three SATA disks on a highpoint rocketraid controller.
       # Start short self-tests daily between 1-2, 2-3, and
       # 3-4 am.
         /dev/sde -d hpt,1/1 -a -s S/../.././01
         /dev/sde -d hpt,1/2 -a -s S/../.././02
         /dev/sde -d hpt,1/3 -a -s S/../.././03
       #
       # Two SATA disks connected to a highpoint rocketraid
       # via a pmport device. Start long self-tests Sundays
       # between midnight and 1am and 2-3 am
         /dev/sde -d hpt,1/4/1 -a -s L/../../7/00
         /dev/sde -d hpt,1/4/2 -a -s L/../../7/02
       #
       # The following line enables monitoring of the
       # ATA Error Log and the Self-Test Error Log.
       # It also tracks changes in both Prefailure
       # and Usage Attributes, apart from Attributes
       # 9, 194, and 231, and shows continued lines:
       #
         /dev/hdd -l error \
                  -l selftest \
                  -t \      # Attributes not tracked:
                  -I 194 \  # temperature
                  -I 231 \  # also temperature
                  -I 9      # power-on hours
       #
       ################################################

CONFIGURATION FILE DIRECTIVES
       If  the  first  non-comment entry in the configuration file is the text
       string DEVICESCAN in capital  letters,  then  smartd  will  ignore  any
       remaining  lines  in the configuration file, and will scan for devices.
       DEVICESCAN may optionally be followed by Directives that will apply  to
       all  devices  that  are  found in the scan.  Please see below for addi-
       tional details.

       The following are the Directives that may appear following  the  device
       name  or  DEVICESCAN  on any line of the /etc/smartd.conf configuration
       file. Note that these are NOT command-line  options  for  smartd.   The
       Directives below may appear in any order, following the device name.

       For  an  ATA  device,  if no Directives appear, then the device will be
       monitored as if the '-a' Directive (monitor all SMART  properties)  had
       been given.

       If  a  SCSI  disk is listed, it will be monitored at the maximum imple-
       mented level: roughly equivalent to using the '-H -l selftest'  options
       for  an  ATA disk.  So with the exception of '-d', '-m', '-l selftest',
       '-s', and '-M', the Directives below are ignored for SCSI  disks.   For
       SCSI  disks, the '-m' Directive sends a warning email if the SMART sta-
       tus indicates a disk failure or problem, if the SCSI inquiry about disk
       status fails, or if new errors appear in the self-test log.

       If a 3ware controller is used then the corresponding SCSI (/dev/sd?) or
       character device (/dev/twe?  or /dev/twa?) must be listed,  along  with
       the  '-d  3ware,N'  Directive  (see  below).   The individual ATA disks
       hosted by the 3ware controller appear to smartd as normal ATA  devices.
       Hence  all the ATA directives can be used for these disks (but see note
       below).

       If a cciss controller is  used  then  the  corresponding  block  device
       (/dev/cciss/c?d?) must be listed, along with the '-d cciss,N' Directive
       (see below).

       -d TYPE
              Specifies the type of the device.  This Directive  may  be  used
              multiple times for one device, but the arguments ata, scsi, sat,
              marvell, cciss and 3ware,N are mutually-exclusive. If more  than
              one is given then smartd will use the last one which appears.

              If  none  of  these  three  arguments is given, then smartd will
              first attempt to guess the device type by looking at whether the
              sixth  character  in  the device name is an 's' or an 'h'.  This
              will work for device names like /dev/hda or /dev/sdb, and corre-
              sponds  to  choosing  ata  or scsi respectively. If smartd can't
              guess from this sixth character, then  it  will  simply  try  to
              access the device using first ATA and then SCSI ioctl()s.

              The valid arguments to this Directive are:

              ata - the device type is ATA.  This prevents smartd from issuing
              SCSI commands to an ATA device.

              scsi - the device type is SCSI.  This prevents smartd from issu-
              ing ATA commands to a SCSI device.

              sat  - the device type is SCSI to ATA Translation (SAT).  smartd
              will generate ATA (smart) commands and then package them in  the
              SAT  defined  ATA  PASS  THROUGH SCSI commands. The commands are
              then routed through the SCSI pass through interface to the oper-
              ating  system. There are two types of ATA PASS THROUGH SCSI com-
              mands: a 12 byte and 16 byte variant.  smartd can use either and
              defaults  to  the  16  byte variant. This can be overridden with
              this syntax: '-d sat,12' or '-d sat,16'.

              marvell - Under Linux, interact with SATA disks  behind  Marvell
              chip-set  controllers  (using  the  Marvell  rather  than libata
              driver).

              3ware,N - the device consists of one or more ATA disks connected
              to  a  3ware RAID controller. The non-negative integer N (in the
              range from 0 to 31 inclusive) denotes which  disk  on  the  con-
              troller is monitored.  In log files and email messages this disk
              will be identified as 3ware_disk_XX with XX in the range from 00
              to 31 inclusive.

              This  Directive may at first appear confusing, because the 3ware
              controller is a SCSI device (such as  /dev/sda)  and  should  be
              listed  as such in the the configuration file.  However when the
              '-d 3ware,N' Directive is used, then the corresponding  disk  is
              addressed  using  native ATA commands which are 'passed through'
              the SCSI driver. All ATA Directives listed in this man page  may
              be used.  Note that while you may use any of the 3ware SCSI log-
              ical devices /dev/sd? to  address  any  of  the  physical  disks
              (3ware  ports),  error and log messages will make the most sense
              if you always list the 3ware SCSI logical  device  corresponding
              to  the  particular physical disks.  Please see the smartctl man
              page for further details.

              ATA disks behind 3ware controllers may alternatively be accessed
              via   a   character   device   interface   /dev/twe0-15   (3ware
              6000/7000/8000 controllers) and /dev/twa0-15 (3ware 9000  series
              controllers).  Note that the 9000 series controllers may only be
              accessed using the character device interface  /dev/twa0-15  and
              not the SCSI device interface /dev/sd?.  Please see the smartctl
              man page for further details.

              Note  that  older  3w-xxxx  drivers  do  not  pass  the  'Enable
              Autosave'  (-S  on)  and 'Enable Automatic Offline' (-o on) com-
              mands to the disk, if the SCSI interface is  used,  and  produce
              these types of harmless syslog error messages instead: '3w-xxxx:
              tw_ioctl(): Passthru size (123392) too big'. This can  be  fixed
              by  upgrading  to  version  1.02.00.037  or later of the 3w-xxxx
              driver,  or  by  applying  a  patch  to  older  versions.    See
              http://smartmontools.sourceforge.net/  for instructions.  Alter-
              natively use the character device interfaces /dev/twe0-15 (3ware
              6/7/8000  series controllers) or /dev/twa0-15 (3ware 9000 series
              controllers).

              cciss,N - the device consists of one or  more  SCSI  disks  con-
              nected  to  a  cciss RAID controller. The non-negative integer N
              (in the range from 0 to 15 inclusive) denotes which disk on  the
              controller  is  monitored.  In log files and email messages this
              disk will be identified as cciss_disk_XX with XX  in  the  range
              from 00 to 15 inclusive.

              3ware  and  cciss controllers are currently ONLY supported under
              Linux.

              hpt,L/M/N - the device consists of one or more  ATA  disks  con-
              nected  to  a  HighPoint RocketRAID controller. The integer L is
              the controller id, the integer M is the channel number, and  the
              integer  N  is the PMPort number if it is available. The allowed
              values of L are from 1 to 4 inclusive, M are from 1 to 8  inclu-
              sive and N from 1 to 4 if PMPort available.  And also these val-
              ues are limited by the model of the  HighPoint  RocketRAID  con-
              troller.   In  log  files  and  email messages this disk will be
              identified as hpt_X/X/X and X/X/X is the same as L/M/N, note  if
              no N indicated, N set to the default value 1.

              HighPoint  RocketRAID  controllers  are currently ONLY supported
              under Linux.

              removable - the device or its media is  removable.   This  indi-
              cates  to  smartd  that  it should continue (instead of exiting,
              which is the default behavior) if the device does not appear  to
              be  present  when smartd is started.  This Directive may be used
              in conjunction with the other '-d' Directives.

       -n POWERMODE[,q]
              This 'nocheck' Directive is used to prevent a  disk  from  being
              spun-up when it is periodically polled by smartd.

              ATA disks have five different power states. In order of increas-
              ing power  consumption  they  are:  'OFF',  'SLEEP',  'STANDBY',
              'IDLE',  and 'ACTIVE'.  Typically in the OFF, SLEEP, and STANDBY
              modes the disk's platters are  not  spinning.  But  usually,  in
              response  to  SMART commands issued by smartd, the disk platters
              are spun up.  So if this option is not used, then a  disk  which
              is  in  a  low-power  mode  may  be  spun  up  and  put  into  a
              higher-power mode when it is periodically polled by smartd.

              Note that if the disk is in SLEEP mode when smartd  is  started,
              then  it won't respond to smartd commands, and so the disk won't
              be registered as a device for smartd to monitor. If a disk is in
              any  other low-power mode, then the commands issued by smartd to
              register the disk will probably cause it to spin-up.

              The '-n' (nocheck)  Directive  specifies  if  smartd's  periodic
              checks  should  still  be  carried  out  when the device is in a
              low-power mode.  It may be used to prevent  a  disk  from  being
              spun-up  by periodic smartd polling.  The allowed values of POW-
              ERMODE are:

              never - smartd will poll (check) the device  regardless  of  its
              power  mode.  This  may  cause  a  disk which is spun-down to be
              spun-up when smartd checks it.  This is the default behavior  if
              the '-n' Directive is not given.

              sleep - check the device unless it is in SLEEP mode.

              standby  -  check  the  device  unless it is in SLEEP or STANDBY
              mode.  In these modes most disks are not  spinning,  so  if  you
              want  to  prevent  a laptop disk from spinning up each time that
              smartd polls, this is probably what you want.

              idle - check the device unless it is in SLEEP, STANDBY  or  IDLE
              mode.  In the IDLE state, most disks are still spinning, so this
              is probably not what you want.

              When a self test is scheduled (see '-s'  Directive  below),  the
              '-n' Directive is ignored, and all tests are carried out.

              When  a  periodic  test  is  skipped,  smartd normally writes an
              informal log message. The message can be suppressed by appending
              the  option  ',q' to POWERMODE (like '-n standby,q').  This pre-
              vents a laptop disk from spinning up due to this message.

       -T TYPE
              Specifies how tolerant smartd should be of SMART  command  fail-
              ures.  The valid arguments to this Directive are:

              normal  -  do  not  try to monitor the disk if a mandatory SMART
              command fails, but continue if an optional SMART command  fails.
              This is the default.

              permissive  - try to monitor the disk even if it appears to lack
              SMART capabilities.  This may be required  for  some  old  disks
              (prior  to  ATA-3  revision 4) that implemented SMART before the
              SMART standards were incorporated into the ATA/ATAPI  Specifica-
              tions.  This may also be needed for some Maxtor disks which fail
              to comply with the ATA Specifications and don't  properly  indi-
              cate support for error- or self-test logging.

              [Please see the smartctl -T command-line option.]

       -o VALUE
              Enables  or disables SMART Automatic Offline Testing when smartd
              starts up and has no further effect.   The  valid  arguments  to
              this Directive are on and off.

              The  delay  between  tests  is vendor-specific, but is typically
              four hours.

              Note that SMART Automatic Offline Testing is not part of the ATA
              Specification.   Please  see the smartctl -o command-line option
              documentation for further information about this feature.

       -S VALUE
              Enables or disables Attribute Autosave when smartd starts up and
              has  no  further  effect.  The valid arguments to this Directive
              are on and off.  Also affects SCSI  devices.   [Please  see  the
              smartctl -S command-line option.]

       -H     Check  the  SMART  health status of the disk.  If any Prefailure
              Attributes are less than or equal  to  their  threshold  values,
              then disk failure is predicted in less than 24 hours, and a mes-
              sage at  loglevel  'LOG_CRITICAL'  will  be  logged  to  syslog.
              [Please see the smartctl -H command-line option.]

       -l TYPE
              Reports  increases  in  the  number  of errors in one of the two
              SMART logs.  The valid arguments to this Directive are:

              error - report if the number of ATA errors reported in  the  ATA
              Error Log has increased since the last check.

              selftest  - report if the number of failed tests reported in the
              SMART Self-Test Log has increased since the last  check,  or  if
              the  timestamp  associated  with the most recent failed test has
              increased.  Note that such errors will only be logged if you run
              self-tests  on  the disk (and it fails a test!).  Self-Tests can
              be run automatically by smartd: please see  the  '-s'  Directive
              below.   Self-Tests  can  also  be  run  manually  by  using the
              '-t short' and '-t long' options of smartctl and the results  of
              the  testing  can  be  observed using the smartctl '-l selftest'
              command-line option.]

              [Please see the smartctl -l and -t command-line options.]

       -s REGEXP
              Run Self-Tests or Offline Immediate Tests, at  scheduled  times.
              A  Self-  or  Offline  Immediate  Test will be run at the end of
              periodic device polling, if all  12  characters  of  the  string
              T/MM/DD/d/HH match the extended regular expression REGEXP. Here:

              T   is the type of the test.  The values that smartd will try to
                  match  (in  turn)  are:  'L' for a Long Self-Test, 'S' for a
                  Short Self-Test, 'C' for a Conveyance Self-Test (ATA  only),
                  and  'O'  for an Offline Immediate Test (ATA only).  As soon
                  as a match is found, the test will be started and  no  addi-
                  tional  matches  will  be  sought  for  that device and that
                  polling cycle.

              MM  is the month of the year, expressed with two decimal digits.
                  The  range  is from 01 (January) to 12 (December) inclusive.
                  Do not use a single decimal digit or the match  will  always
                  fail!

              DD  is  the day of the month, expressed with two decimal digits.
                  The range is from 01 to 31 inclusive.  Do not use  a  single
                  decimal digit or the match will always fail!

              d   is  the  day  of the week, expressed with one decimal digit.
                  The range is from 1 (Monday) to 7 (Sunday) inclusive.

              HH  is the hour of the day, written with two decimal digits, and
                  given in hours after midnight.  The range is 00 (midnight to
                  just before 1am) to 23 (11pm to just before midnight) inclu-
                  sive.   Do  not use a single decimal digit or the match will
                  always fail!

              Some examples follow.  In reading these, keep in  mind  that  in
              extended  regular expressions a dot '.' matches any single char-
              acter, and a parenthetical expression such as '(A|B|C)'  denotes
              any one of the three possibilities A, B, or C.

              To schedule a short Self-Test between 2-3am every morning, use:
               -s S/../.././02
              To schedule a long Self-Test between 4-5am every Sunday morning,
              use:
               -s L/../../7/04
              To schedule a long Self-Test between 10-11pm on  the  first  and
              fifteenth day of each month, use:
               -s L/../(01|15)/./22
              To schedule an Offline Immediate test after every midnight, 6am,
              noon,and 6pm, plus a Short Self-Test daily at 1-2am and  a  Long
              Self-Test every Saturday at 3-4am, use:
               -s (O/../.././(00|06|12|18)|S/../.././01|L/../../6/03)

              Scheduled  tests  are  run  immediately following the regularly-
              scheduled device polling, if the current local date,  time,  and
              test  type,  match  REGEXP.   By default the regularly-scheduled
              device  polling  occurs  every  thirty  minutes  after  starting
              smartd.   Take  caution  if you use the '-i' option to make this
              polling interval more than sixty minutes:  the  poll  times  may
              fail  to  coincide  with  any of the testing times that you have
              specified with REGEXP, and so the self tests may not take  place
              as you wish.

              Before running an offline or self-test, smartd checks to be sure
              that a self-test is not already  running.   If  a  self-test  is
              already  running, then this running self test will not be inter-
              rupted to begin another test.

              smartd will not attempt to run any type of test if another  test
              was already started or run in the same hour.

              To  avoid  performance  problems during system boot, smartd will
              not attempt to run any scheduled tests following the very  first
              device polling (unless '-q onecheck' is specified).

              Each  time  a  test  is run, smartd will log an entry to SYSLOG.
              You can use these or the '-q showtests' command-line  option  to
              verify  that  you  constructed  REGEXP  correctly.  The matching
              order (L before S before C before O) ensures  that  if  multiple
              test  types are all scheduled for the same hour, the longer test
              type has precedence.  This is usually the desired behavior.

              Unix users: please beware that the rules  for  extended  regular
              expressions  [regex(7)]  are  not  the  same  as  the  rules for
              file-name pattern matching by the shell [glob(7)].  smartd  will
              issue  harmless  informational  warning  messages  if it detects
              characters in REGEXP that appear to indicate that you have  made
              this mistake.

       -m ADD Send a warning email to the email address ADD if the '-H', '-l',
              '-f', '-C', or '-O' Directives detect a failure or a new  error,
              or  if  a  SMART  command to the disk fails. This Directive only
              works in conjunction with these other Directives  (or  with  the
              equivalent default '-a' Directive).

              To prevent your email in-box from getting filled up with warning
              messages, by default only a single warning will be sent for each
              of the enabled alert types, '-H', '-l', '-f', '-C', or '-O' even
              if more than one failure or error is detected or if the  failure
              or error persists.  [This behavior can be modified; see the '-M'
              Directive below.]

              To send email to more than one user, please  use  the  following
              "comma      separated"      form      for      the      address:
              user1@add1,user2@add2,...,userN@addN (with no spaces).

              To test that email is being sent correctly, use  the  '-M  test'
              Directive  described  below  to  send  one test email message on
              smartd startup.

              By default, email is sent using the  system  mail  command.   In
              order  that smartd find the mail command (normally /bin/mail) an
              executable named 'mail' must be in the  path  of  the  shell  or
              environment from which smartd was started.  If you wish to spec-
              ify an  explicit  path  to  the  mail  executable  (for  example
              /usr/local/bin/mail)  or  a custom script to run, please use the
              '-M exec' Directive below.

              Note that by default under Solaris, in the  previous  paragraph,
              'mailx'  and  '/bin/mailx'  are  used, since Solaris '/bin/mail'
              does not accept a '-s' (Subject) command-line argument.

              On Windows, the 'Blat' mailer (http://blat.sourceforge.net/)  is
              used by default.  This mailer uses a different command line syn-
              tax, see '-M exec' below.

              Note also that there is a special argument <nomailer> which  can
              be given to the '-m' Directive in conjunction with the '-M exec'
              Directive. Please see below for an explanation of its effect.

              If the mailer or the shell running it produces any STDERR/STDOUT
              output,  then a snippet of that output will be copied to SYSLOG.
              The remainder of  the  output  is  discarded.  If  problems  are
              encountered  in sending mail, this should help you to understand
              and fix them.  If you have mail problems, we  recommend  running
              smartd  in  debug  mode  with the '-d' flag, using the '-M test'
              Directive described below.

              The following extension is available on Windows:  By  specifying
              'msgbox'  as a mail address, a warning "email" is displayed as a
              message box on the screen.  Using both 'msgbox' and regular mail
              addresses  is  possible,  if  'msgbox'  is the first word in the
              comma separated list.  With 'sysmsgbox', a system modal  (always
              on  top) message box is used. If running as a service, a service
              notification message box (always shown on current visible  desk-
              top) is used.

       -M TYPE
              These  Directives  modify the behavior of the smartd email warn-
              ings enabled with the  '-m'  email  Directive  described  above.
              These  '-M'  Directives  only  work in conjunction with the '-m'
              Directive and can not be used without it.

              Multiple -M Directives may be given.  If more than  one  of  the
              following  three  -M  Directives  are given (example: -M once -M
              daily) then the final one (in the example, -M daily) is used.

              The valid arguments to the -M Directive are (one of the  follow-
              ing three):

              once - send only one warning email for each type of disk problem
              detected.  This is the default.

              daily - send additional warning reminder emails, once  per  day,
              for each type of disk problem detected.

              diminishing  -  send additional warning reminder emails, after a
              one-day interval, then  a  two-day  interval,  then  a  four-day
              interval, and so on for each type of disk problem detected. Each
              interval is twice as long as the previous interval.

              In addition, one may add zero or more of  the  following  Direc-
              tives:

              test - send a single test email immediately upon smartd startup.
              This allows one to verify that  email  is  delivered  correctly.
              Note  that  if this Directive is used, smartd will also send the
              normal email warnings that were enabled with the '-m' Directive,
              in addition to the single test email!

              exec  PATH - run the executable PATH instead of the default mail
              command, when smartd needs to send email.  PATH must point to an
              executable binary file or script.

              By  setting  PATH  to point to a customized script, you can make
              smartd perform useful tricks when a  disk  problem  is  detected
              (beeping  the  console,  shutting down the machine, broadcasting
              warnings to all logged-in users, etc.)  But please  be  careful.
              smartd  will block until the executable PATH returns, so if your
              executable hangs,  then  smartd  will  also  hang.  Some  sample
              scripts  are  included  in /usr/share/doc/smartmontools/example-
              scripts/.

              The return status of the executable is  recorded  by  smartd  in
              SYSLOG.  The  executable  is  not expected to write to STDOUT or
              STDERR.  If it does, then this is interpreted as indicating that
              something is going wrong with your executable, and a fragment of
              this output is logged to SYSLOG to help you  to  understand  the
              problem.  Normally, if you wish to leave some record behind, the
              executable should send mail or write to a file or device.

              Before running the executable, smartd sets a number of  environ-
              ment variables.  These environment variables may be used to con-
              trol  the  executable's  behavior.   The  environment  variables
              exported by smartd are:

              SMARTD_MAILER
                  is  set  to  the  argument of -M exec, if present or else to
                  'mail' (examples: /bin/mail, mail).

              SMARTD_DEVICE
                  is set to the device path (examples: /dev/hda, /dev/sdb).

              SMARTD_DEVICETYPE
                  is set to the  device  type  (possible  values:  ata,  scsi,
                  3ware,N,  cciss,N,  hpt,L/M/N).  Here N=0,...,23 denotes the
                  ATA disk behind a 3ware or cciss RAID controller  and  L/M/N
                  denotes  the  SATA  disk  behind a HighPoint RocketRAID con-
                  troller.

              SMARTD_DEVICESTRING
                  is set to the device description.  For SMARTD_DEVICETYPE  of
                  ata  or  scsi, this is the same as SMARTD_DEVICE.  For 3ware
                  RAID   controllers,   the    form    used    is    '/dev/sdc
                  [3ware_disk_01]'.   For HighPoint RocketRAID controller, the
                  form is '/dev/sdd [hpt_1/1/1]'.  In these cases  the  device
                  string  contains  a  space  and  is  NOT  quoted.  So to use
                  $SMARTD_DEVICESTRING in a bash script  you  should  probably
                  enclose it in double quotes.

              SMARTD_FAILTYPE
                  gives the reason for the warning or message email.  The pos-
                  sible values that it takes and their meanings are:
                  EmailTest: this is an email test message.
                  Health: the SMART health status indicates imminent  failure.
                  Usage: a usage Attribute has failed.
                  SelfTest: the number of self-test failures has increased.
                  ErrorCount:  the  number  of errors in the ATA error log has
                  increased.
                  CurrentPendingSector: one of more disk sectors could not  be
                  read  and  are marked to be reallocated (replaced with spare
                  sectors).
                  OfflineUncorrectableSector:  during  off-line  testing,   or
                  self-testing, one or more disk sectors could not be read.
                  FailedHealthCheck: the SMART health status command failed.
                  FailedReadSmartData:  the  command  to  read SMART Attribute
                  data failed.
                  FailedReadSmartErrorLog: the command to read the SMART error
                  log failed.
                  FailedReadSmartSelfTestLog:  the  command  to read the SMART
                  self-test log failed.
                  FailedOpenDevice: the open() command to the device failed.

              SMARTD_ADDRESS
                  is determined by the address argument ADD of the '-m' Direc-
                  tive.  If ADD is <nomailer>, then SMARTD_ADDRESS is not set.
                  Otherwise, it is set to the  comma-separated-list  of  email
                  addresses  given  by  the  argument  ADD,  with  the  commas
                  replaced by  spaces  (example:admin@example.com  root).   If
                  more  than one email address is given, then this string will
                  contain space characters and is NOT quoted, so to use it  in
                  a bash script you may want to enclose it in double quotes.

              SMARTD_MESSAGE
                  is  set  to  the  one sentence summary warning email message
                  string from smartd.   This  message  string  contains  space
                  characters and is NOT quoted. So to use $SMARTD_MESSAGE in a
                  bash script you should probably enclose it in double quotes.

              SMARTD_FULLMESSAGE
                  is  set  to the contents of the entire email warning message
                  string from smartd.  This message string contains space  and
                  return   characters   and   is   NOT   quoted.   So  to  use
                  $SMARTD_FULLMESSAGE in a bash  script  you  should  probably
                  enclose it in double quotes.

              SMARTD_TFIRST
                  is a text string giving the time and date at which the first
                  problem of this type was reported. This text string contains
                  space  characters  and  no  newlines, and is NOT quoted. For
                  example:
                  Sun Feb  9 14:58:19 2003 CST

              SMARTD_TFIRSTEPOCH
                  is an integer, which is the unix epoch  (number  of  seconds
                  since Jan 1, 1970) for SMARTD_TFIRST.

              The  shell  which  is  used to run PATH is system-dependent. For
              vanilla Linux/glibc it's bash. For other systems, the  man  page
              for popen(3) should say what shell is used.

              If  the  '-m ADD' Directive is given with a normal address argu-
              ment, then the executable pointed to by PATH will be  run  in  a
              shell  with  STDIN  receiving the body of the email message, and
              with the same command-line arguments:
              -s "$SMARTD_SUBJECT" $SMARTD_ADDRESS
              that would normally be provided to 'mail'.  Examples include:
              -m user@home -M exec /bin/mail
              -m admin@work -M exec /usr/local/bin/mailto
              -m root -M exec /Example_1/bash/script/below

              Note that on Windows, the syntax of the 'Blat' mailer is used:
              - -q -subject "$SMARTD_SUBJECT" -to "$SMARTD_ADDRESS"

              If the '-m ADD' Directive is  given  with  the  special  address
              argument  <nomailer>  then  the executable pointed to by PATH is
              run in a shell with no STDIN and no command-line arguments,  for
              example:
              -m <nomailer> -M exec /Example_2/bash/script/below
              If the executable produces any STDERR/STDOUT output, then smartd
              assumes that something is going wrong, and  a  snippet  of  that
              output will be copied to SYSLOG.  The remainder of the output is
              then discarded.

              Some EXAMPLES of scripts that can be used  with  the  '-M  exec'
              Directive are given below. Some sample scripts are also included
              in /usr/share/doc/smartmontools/examplescripts/.

       -f     Check  for  'failure'  of  any  Usage  Attributes.    If   these
              Attributes  are less than or equal to the threshold, it does NOT
              indicate imminent disk failure.  It "indicates an advisory  con-
              dition  where  the  usage  or age of the device has exceeded its
              intended design life period."  [Please see the smartctl -A  com-
              mand-line option.]

       -p     Report  anytime  that  a Prefail Attribute has changed its value
              since the last check, 30 minutes ago. [Please see  the  smartctl
              -A command-line option.]

       -u     Report  anytime  that  a  Usage  Attribute has changed its value
              since the last check, 30 minutes ago. [Please see  the  smartctl
              -A command-line option.]

       -t     Equivalent  to  turning on the two previous flags '-p' and '-u'.
              Tracks changes in all device  Attributes  (both  Prefailure  and
              Usage). [Please see the smartctl -A command-line option.]

       -i ID  Ignore  device  Attribute number ID when checking for failure of
              Usage Attributes.  ID must be a decimal  integer  in  the  range
              from 1 to 255.  This Directive modifies the behavior of the '-f'
              Directive and has no effect without it.

              This is useful, for example, if you have a  very  old  disk  and
              don't  want to keep getting messages about the hours-on-lifetime
              Attribute (usually Attribute 9)  failing.   This  Directive  may
              appear multiple times for a single device, if you want to ignore
              multiple Attributes.

       -I ID  Ignore  device  Attribute  ID  when  tracking  changes  in   the
              Attribute  values.   ID  must  be a decimal integer in the range
              from 1 to 255.  This Directive  modifies  the  behavior  of  the
              '-p', '-u', and '-t' tracking Directives and has no effect with-
              out one of them.

              This is useful, for example, if one of the device Attributes  is
              the disk temperature (usually Attribute 194 or 231). It's annoy-
              ing to get reports each  time  the  temperature  changes.   This
              Directive  may appear multiple times for a single device, if you
              want to ignore multiple Attributes.

       -r ID  When tracking, report the Raw value of Attribute ID  along  with
              its  (normally reported) Normalized value.  ID must be a decimal
              integer in the range from 1 to 255.  This Directive modifies the
              behavior of the '-p', '-u', and '-t' tracking Directives and has
              no effect without one of them.  This Directive may be given mul-
              tiple times.

              A  common  use of this Directive is to track the device Tempera-
              ture (often ID=194 or 231).

       -R ID  When tracking, report whenever the Raw  value  of  Attribute  ID
              changes.   (Normally  smartd  only tracks/reports changes of the
              Normalized Attribute values.)  ID must be a decimal  integer  in
              the  range  from 1 to 255.  This Directive modifies the behavior
              of the '-p', '-u', and  '-t'  tracking  Directives  and  has  no
              effect  without one of them.  This Directive may be given multi-
              ple times.

              If this Directive is given, it automatically  implies  the  '-r'
              Directive  for  the same Attribute, so that the Raw value of the
              Attribute is reported.

              A common use of this Directive is to track the  device  Tempera-
              ture (often ID=194 or 231).  It is also useful for understanding
              how different types of system behavior  affects  the  values  of
              certain Attributes.

       -C ID  [ATA  only]  Report  if the current number of pending sectors is
              non-zero.  Here ID is the id number of the Attribute  whose  raw
              value is the Current Pending Sector count.  The allowed range of
              ID is 0 to 255 inclusive.   To  turn  off  this  reporting,  use
              ID = 0.   If  the -C ID option is not given, then it defaults to
              -C 197 (since Attribute 197 is generally used to monitor pending
              sectors).

              A  pending sector is a disk sector (containing 512 bytes of your
              data) which the device would like to mark as ``bad" and  reallo-
              cate.   Typically  this  is  because your computer tried to read
              that sector, and the read failed because the data on it has been
              corrupted  and  has  inconsistent  Error Checking and Correction
              (ECC) codes.  This is important to know, because it  means  that
              there  is some unreadable data on the disk.  The problem of fig-
              uring out what file this data belongs to is operating system and
              file  system  specific.   You  can typically force the sector to
              reallocate by writing to it (translation: make the  device  sub-
              stitute a spare good sector for the bad one) but at the price of
              losing the 512 bytes of data stored there.

       -U ID  [ATA only] Report if the number of offline uncorrectable sectors
              is  non-zero.   Here  ID is the id number of the Attribute whose
              raw value  is  the  Offline  Uncorrectable  Sector  count.   The
              allowed  range  of  ID  is 0 to 255 inclusive.  To turn off this
              reporting, use ID = 0.  If the -U ID option is not  given,  then
              it  defaults to -U 198 (since Attribute 198 is generally used to
              monitor offline uncorrectable sectors).

              An offline uncorrectable sector is a disk sector which  was  not
              readable during an off-line scan or a self-test.  This is impor-
              tant to know, because if you have data stored in this disk  sec-
              tor,  and  you  need to read it, the read will fail.  Please see
              the previous '-C' option for more details.

       -W DIFF[,INFO[,CRIT]]
              Report if the current temperature had changed by at  least  DIFF
              degrees  since last report. Report or Warn if the temperature is
              greater or equal than one of INFO or CRIT  degrees  Celsius.  If
              the  limit  CRIT is reached, a message with loglevel 'LOG_CRITI-
              CAL' will be logged to syslog and a warning email will  be  send
              if  '-m' is specified. If only the limit INFO is reached, a mes-
              sage with loglevel 'LOG_INFO' will be logged.

              To disable any of the 3 reports, set the corresponding limit  to
              0.  Trailing zero arguments may be omitted. By default, all tem-
              perature reports are disabled ('-W 0').

              To track temperature changes of at least 2 degrees, use:
               -W 2
              To log informal messages on temperatures of at least 40 degrees,
              use:
               -W 0,40
              For  warning  messages/mails  on  temperatures  of  at  least 45
              degrees, use:
               -W 0,0,45
              To combine all of the above reports, use:
               -W 2,40,45

              For ATA devices, smartd interprets Attribute 194 as  Temperature
              Celsius by default. This can be changed to Attribute 9 or 220 by
              the drive database or by the '-v' directive, see below.

       -F TYPE
              [ATA only] Modifies the behavior of  smartd  to  compensate  for
              some known and understood device firmware bug.  The arguments to
              this Directive are exclusive, so that only the  final  Directive
              given is used.  The valid values are:

              none  - Assume that the device firmware obeys the ATA specifica-
              tions.  This is the default, unless the device has  presets  for
              '-F' in the device database.

              samsung - In some Samsung disks (example: model SV4012H Firmware
              Version: RM100-08) some of the two- and four-byte quantities  in
              the  SMART data structures are byte-swapped (relative to the ATA
              specification).  Enabling this option tells smartd  to  evaluate
              these  quantities  in byte-reversed order.  Some signs that your
              disk needs this option are (1) no self-test  log  printed,  even
              though  you  have  run self-tests; (2) very large numbers of ATA
              errors reported in the ATA error log; (3) strange and impossible
              values for the ATA error log timestamps.

              samsung2 - In more recent Samsung disks (firmware revisions end-
              ing in "-23") the number of ATA errors reported is byte swapped.
              Enabling  this  option tells smartd to evaluate this quantity in
              byte-reversed order.

              samsung3 - Some Samsung disks (at least  SP2514N  with  Firmware
              VF100-37) report a self-test still in progress with 0% remaining
              when the test was already completed. If this directive is speci-
              fied,  smartd  will  not  skip the next scheduled self-test (see
              Directive '-s' above) in this case.

              Note that an explicit '-F' Directive will over-ride  any  preset
              values for '-F' (see the '-P' option below).

              [Please see the smartctl -F command-line option.]

       -v N,OPTION
              Modifies  the labeling for Attribute N, for disks which use non-
              standard Attribute definitions.  This is  useful  in  connection
              with the Attribute tracking/reporting Directives.

              This  Directive  may  appear  multiple times. Valid arguments to
              this Directive are:

              9,minutes - Raw Attribute number 9 is power-on time in  minutes.
              Its  raw value will be displayed in the form 'Xh+Ym'.  Here X is
              hours, and Y is minutes in  the  range  0-59  inclusive.   Y  is
              always  printed  with  two  digits,  for example '06' or '31' or
              '00'.

              9,seconds - Raw Attribute number 9 is power-on time in  seconds.
              Its  raw value will be displayed in the form 'Xh+Ym+Zs'.  Here X
              is hours, Y is minutes in the range 0-59  inclusive,  and  Z  is
              seconds in the range 0-59 inclusive.  Y and Z are always printed
              with two digits, for example '06' or '31' or '00'.

              9,halfminutes  -  Raw  Attribute  number  9  is  power-on  time,
              measured  in  units  of 30 seconds.  This format is used by some
              Samsung disks.  Its raw value will  be  displayed  in  the  form
              'Xh+Ym'.   Here  X  is hours, and Y is minutes in the range 0-59
              inclusive.  Y is always printed with  two  digits,  for  example
              '06' or '31' or '00'.

              9,temp  - Raw Attribute number 9 is the disk temperature in Cel-
              sius.

              192,emergencyretractcyclect - Raw Attribute number  192  is  the
              Emergency Retract Cycle Count.

              193,loadunload  -  Raw Attribute number 193 contains two values.
              The first is the number of load cycles.  The second is the  num-
              ber  of  unload cycles.  The difference between these two values
              is the number of times that the drive was  unexpectedly  powered
              off  (also  called an emergency unload). As a rule of thumb, the
              mechanical stress created by one emergency unload is  equivalent
              to that created by one hundred normal unloads.

              194,10xCelsius  - Raw Attribute number 194 is ten times the disk
              temperature in Celsius.  This is  used  by  some  Samsung  disks
              (example: model SV1204H with RK100-13 firmware).

              194,unknown  - Raw Attribute number 194 is NOT the disk tempera-
              ture, and its interpretation is unknown. This is primarily  use-
              ful for the -P (presets) Directive.

              198,offlinescanuncsectorct  -  Raw  Attribute  number 198 is the
              Offline Scan UNC Sector Count.

              200,writeerrorcount - Raw Attribute  number  200  is  the  Write
              Error Count.

              201,detectedtacount  -  Raw Attribute number 201 is the Detected
              TA Count.

              220,temp - Raw Attribute number 220 is the disk  temperature  in
              Celsius.

              Note: a table of hard drive models, listing which Attribute cor-
              responds    to     temperature,     can     be     found     at:
              http://www.guzu.net/linux/hddtemp.db

              N,raw8  -  Print  the  Raw  value  of  Attribute  N as six 8-bit
              unsigned base-10 integers.  This may be useful for decoding  the
              meaning  of  the Raw value.  The form 'N,raw8' prints Raw values
              for ALL  Attributes  in  this  form.   The  form  (for  example)
              '123,raw8'  only  prints the Raw value for Attribute 123 in this
              form.

              N,raw16 - Print the Raw value of Attribute  N  as  three  16-bit
              unsigned  base-10 integers.  This may be useful for decoding the
              meaning of the Raw value.  The form 'N,raw16' prints Raw  values
              for  ALL  Attributes  in  this  form.   The  form  (for example)
              '123,raw16' only prints the Raw value for Attribute 123 in  this
              form.

              N,raw48  -  Print  the  Raw  value  of  Attribute  N as a 48-bit
              unsigned base-10 integer.  This may be useful for  decoding  the
              meaning  of the Raw value.  The form 'N,raw48' prints Raw values
              for ALL  Attributes  in  this  form.   The  form  (for  example)
              '123,raw48'  only prints the Raw value for Attribute 123 in this
              form.

       -P TYPE
              Specifies whether smartd should use any preset options that  are
              available for this drive.  The valid arguments to this Directive
              are:

              use - use any presets that are available for this  drive.   This
              is the default.

              ignore - do not use any presets for this drive.

              show - show the presets listed for this drive in the database.

              showall - show the presets that are available for all drives and
              then exit.

              [Please see the smartctl -P command-line option.]

       -a     Equivalent to turning on all of the following  Directives:  '-H'
              to  check  the  SMART  health status, '-f' to report failures of
              Usage (rather than Prefail) Attributes, '-t' to track changes in
              both  Prefailure  and  Usage Attributes, '-l selftest' to report
              increases in the number of Self-Test Log errors,  '-l error'  to
              report increases in the number of ATA errors, '-C 197' to report
              nonzero values of the current pending sector count, and '-U 198'
              to report nonzero values of the offline pending sector count.

              Note  that  -a is the default for ATA devices.  If none of these
              other Directives is given, then -a is assumed.

       #      Comment: ignore the remainder of the line.

       \      Continuation character: if this is the last  non-white  or  non-
              comment  character  on a line, then the following line is a con-
              tinuation of the current one.

       If you are not sure which Directives to use,  I  suggest  experimenting
       for  a  few  minutes with smartctl to see what SMART functionality your
       disk(s) support(s).  If you do not like voluminous syslog  messages,  a
       good choice of smartd configuration file Directives might be:
       -H -l selftest -l error -f.
       If you want more frequent information, use: -a.

       ADDITIONAL DETAILS ABOUT DEVICESCAN
              If  the first non-comment entry in the configuration file is the
              text string DEVICESCAN in  capital  letters,  then  smartd  will
              ignore  any  remaining lines in the configuration file, and will
              scan for devices.

              If DEVICESCAN is not followed by  any  Directives,  then  smartd
              will  scan  for  both ATA and SCSI devices, and will monitor all
              possible SMART properties of any devices that are found.

              DEVICESCAN may optionally be followed by any  valid  Directives,
              which will be applied to all devices that are found in the scan.
              For example
              DEVICESCAN -m root@example.com
              will scan for all devices, and then monitor them.  It will  send
              one email warning per device for any problems that are found.
              DEVICESCAN -d ata -m root@example.com
              will do the same, but restricts the scan to ATA devices only.
              DEVICESCAN -H -d ata -m root@example.com
              will  do  the same, but only monitors the SMART health status of
              the devices, (rather than the default  -a,  which  monitors  all
              SMART properties).

       EXAMPLES OF SHELL SCRIPTS FOR '-M exec'
              These  are  two  examples of shell scripts that can be used with
              the '-M exec PATH' Directive described previously.  The paths to
              these  scripts  and  similar executables is the PATH argument to
              the '-M exec PATH' Directive.

              Example 1: This script is for  use  with  '-m  ADDRESS  -M  exec
              PATH'.   It  appends  the output of smartctl -a to the output of
              the smartd email warning message and sends it to ADDRESS.

              #! /bin/bash

              # Save the email message (STDIN) to a file:
              cat > /root/msg

              # Append the output of smartctl -a to the message:
              /usr/sbin/smartctl -a -d $SMART_DEVICETYPE $SMARTD_DEVICE >> /root/msg

              # Now email the message to the user at address ADD:
              /bin/mail -s "$SMARTD_SUBJECT" $SMARTD_ADDRESS < /root/msg

              Example 2: This script is for use with '-m  <nomailer>  -M  exec
              PATH'.  It  warns  all users about a disk problem, waits 30 sec-
              onds, and then powers down the machine.

              #! /bin/bash

              # Warn all users of a problem
              wall 'Problem detected with disk: ' "$SMARTD_DEVICESTRING"
              wall 'Warning message from smartd is: ' "$SMARTD_MESSAGE"
              wall 'Shutting down machine in 30 seconds... '

              # Wait half a minute
              sleep 30

              # Power down the machine
              /sbin/shutdown -hf now

              Some example scripts  are  distributed  with  the  smartmontools
              package, in /usr/share/doc/smartmontools/examplescripts/.

              Please  note  that  these  scripts typically run as root, so any
              files that they read/write should not be  writable  by  ordinary
              users  or  reside  in directories like /tmp that are writable by
              ordinary users and may expose your system to symlink attacks.

              As previously described, if  the  scripts  write  to  STDOUT  or
              STDERR,  this  is  interpreted  as  indicating that there was an
              internal error within the script, and a snippet of STDOUT/STDERR
              is logged to SYSLOG.  The remainder is flushed.

AUTHOR
       Bruce Allen smartmontools-support@lists.sourceforge.net
       University of Wisconsin - Milwaukee Physics Department

CONTRIBUTORS
       The following have made large contributions to smartmontools:
       Casper Dik (Solaris SCSI interface)
       Christian Franke (Windows interface and Cygwin package)
       Douglas Gilbert (SCSI subsystem)
       Guido Guenther (Autoconf/Automake packaging)
       Geoffrey Keating (Darwin ATA interface)
       Eduard Martinescu (FreeBSD interface)
       Frederic L. W. Meunier (Web site and Mailing list)
       Keiji Sawada (Solaris ATA interface)
       Sergey Svishchev (NetBSD interface)
       David Snyder and Sergey Svishchev (OpenBSD interface)
       Phil Williams (User interface and drive database)
       Shengfeng Zhou (Linux Highpoint RocketRaid interface)
       Many other individuals have made smaller contributions and corrections.

CREDITS
       This code was derived from the smartsuite package, written  by  Michael
       Cornwell,  and  from  the  previous ucsc smartsuite package. It extends
       these to cover ATA-5 disks. This code was  originally  developed  as  a
       Senior  Thesis by Michael Cornwell at the Concurrent Systems Laboratory
       (now part of the Storage Systems Research Center), Jack  Baskin  School
       of    Engineering,    University    of    California,    Santa    Cruz.
       http://ssrc.soe.ucsc.edu/ .

HOME PAGE FOR SMARTMONTOOLS:
       Please see the following web site for updates,  further  documentation,
       bug reports and patches:
       http://smartmontools.sourceforge.net/

SEE ALSO:
       smartd(8),   smartctl(8),   syslogd(8),  syslog.conf(5),  badblocks(8),
       ide-smart(8), regex(7).

CVS ID OF THIS PAGE:
       $Id: smartd.conf.5.in,v 1.87 2008/03/04 22:09:47 ballen4705 Exp $

smartmontools-5.38                2008/03/10                    SMARTD.CONF(5)

Time taken: 0.00053 seconds


Created with the man page lookup class by Andrew Collington, php@amnuts.com